BCIS stands for Building Cost Information Service. It’s a service provided by the Royal Institution of Chartered Surveyors (RICS) that offe...

Material Properties and Dimensions: These are the basic inputs required for the calculations, including the weights of concrete and soil, dimen...

The AISC (American Institute of Steel Construction) 2016 specification provides guidelines for the design and construction of structural steel buil...

This calculation pertains to the structural analysis of a specific bridge component—Bridge 1 - Crossing 1&mda...

IS 456:2000 is a code of practice published by the Bureau of Indian Standards (BIS) for the design and constructi...

The MS-Excel spreadsheet program designed for the analysis of steel column base plates serves as a comprehensive engineering tool catering ...

Includes details for bolting clearances for below list :OPEN JAW WRENCHESSINGLE ENDED OPEN JAW SLUGGING WRENCHESSOCKET WR...

Roof live load calculations in ASCE 7-10 Section 4.8.2:The roof live load is calculated using Equation 4.8-1:Lr = Lo R1 R2 Where:Lr ...

a comprehenisve list of all Europeon Steel section Data taken from Dlubal (website https://www.dlubal.com/en/cross-section-properties). Documented ...

In bearing type connections, the bolts are not pretensioned and the shear is resisted by bearing on the bolt hole. When these connections a...

A slip-critical connection, as defined by the American Institute of Steel Construction (AISC), is a type of bolted connection where sli...

Design of Anchorage Bolt at Truss Support to BS En 1993. Spreadsheet to check and input of MS anchorage bolt at the end of a truss. The input value...

Roof Purlin design to S EN 1993. Excel file on design of a metal purlin for roof either metal decking or clay tile roof. The design spreadsheet all...

\

Storm water drainage calculation

Stormwater calculations are essential for designing and managing stormwater systems, which are responsibl...

sHEAR END PLATE DESIGN AS PER EN 1993-1-8

EN 1991-1-8, part of the Eurocode suite of standards, provides guidelines for designing steel st...

RC design based on EN 1992

Seimic Response of Liquid Storage Tank

ASCE 7-10, 'Minimum Design Loads for Buildings and Other Structures,' is a standard developed by the American Society o...

The 'Code of Practice for Structural Use of Concrete 2013' is a design manual provided by the Buildings Department of the Hong Kong Government. It ...

Footing Bending Stress The Structural Designers Foundation Manual provides guidelines for calculating bending stress in footings, which are critic...

Modulus of subgrade reaction or coefficient of subgrade reaction is the reaction pressure sustained by the soil sample under a rigid plate of s...

ACI 318-2014

DESIGN OF CANTILEVER RETAINING WALL WITH SURCHARGE OVER BACKFILL

DESIGN OF COUNTERFORT RETAINING WALL WITH FRONT AND REAR COUN...

Spreadsheet Description: Computes the depth required, maximum moment, and section modulus required for Sheet Pile Design based on US Steel's Sheet...

This is for infiltration testing requirements for Riverside County (California). A percolation test (colloquially called a perc test)...

Slab on grade concentrated wheel load check per ACI 360R-06.

Design of magnum stone retaining wall

Quick PGA calculator based on NZTA Bridge manual. with extracts From BM and ASNZ 1170.0.

Steel base plates are generally used under columns for distribution of the column load over a sufficient area of the concrete pier or foundation....

Design of One Way slab, Design of Two way slab, Design of Column , Design of Beam, Design of Footings , Design of Staircase Complete Pack...

ACI 318-11 Crack Width Calculations For Slab. 1 - Locate the Neutral axis & Calculate section properties: 2 - Check of Concrete &...

Calculation Description: 'GRDSLAB' is a spreadsheet program written in MS-Excel for the purpose of analysis of conc...

BRIDGE DESIGN TO AASHTO LRFD 2007

BRIDGE GENERAL DATA

GIRDER DIMENSIONS

PRECAST SECTION
COMPOSITE SECTION
ELASTOM...